D-Linkap.local | 192.168.0.50 Login

 

Dlink Extender Setup and 192.168.0.50 Login Guide
Do you want to perform Dlink Extender Setup either using 192.168.0.50 Login or dlinkap.local web address. It not only decreases the interferences in the way of WiFi signals but also provides compatibility with other WiFi devices. Here, in this blog, we discuss how to access dlinkap.local for the Dlink extender local setup. Let’s go ahead.

Setup dlink range extender
Device frame
  • 1

    Know About Dlink Extender Setup

     

    Dlink extender setup wizard enables the users to configure the D-Link extender device and resolves all the internet connectivity issues. If you want to improve the network connectivity at each and every corner of your home, you have to access dlinkap.local login and follow the on-screen instructions for Dlink extender local setup.

    Steps for Dlink Extender Local Login

    Go through the below instructions for the Dlink Extender Login on your device:

    Step 1: The first step is to place the D-Link extender in an appropriate place.

    Step 2: After that, take an Ethernet cable and use it to connect your computer with the Dlink range extender.

    Step 3: Thereafter, plug your extender into the power socket and turn it on.

    Step 4: Connect your D-link device to the wireless network.

    Step 5: Open any web browser of your choice and enter the default web address http://dlinkap.local admin login in the address bar.

    Note: If this web address does not work for you to access the Dlink extender local login, use the IP address 192.168.0.50 Login.

    Step 6: Once you reach the Dlink extender login, enter the default username and password in the respective fields.

    Step 7: Click on the Login button.

    Note: If you do not know the default login credential details, you can look for this information on the printed label at the bottom of your extender. Note down the details safely as it is required during the Dlink Extender Setup process.

    Know about dlink extender setup
  • 2

    Instructions for the Dlink Extender Local Setup

     The process of Dlink extender setup is simple, but some users found it so much more difficult. The users can set up their extender either through a web browser or the WPS method. In this section, we have described both methods in detail. 

    Dlink 1
  • 3

    Method 1: Set up D-Link Extender through Web Browser

     

    • The first step is to connect the Dlink range extender to the computer using the Ethernet cable.
    • After that, open the wireless utility on your system.
    • Next, choose the network name of your D-Link extender. Enter the password for the network name if required.
    • Open a web browser on your computer. Enter the default web address http://dlinkap.local admin login or IP address 192.168.0.50 login in the address bar of the web browser.
    • It will redirect you to the D-Link extender login web page. Enter the login credential details in the respective fields.
    • Click on the login button.
    • When you reach the configuration webpage, tap on the “setup” button.
    • Open the D-Link extender setup wizard and follow on-screen instructions.
    • Next, configure the wireless and security settings for your D-Link device.

    At last, tap on the “Finish” button to complete the Dlink Extender Setup. Once the setup process is completed, reboot your device.

    Set up D-Link Extender through Web Browser
  • 4

    Method 2: Set up D-Link Extender Using WPS Method

     

    • Firstly, place the D-Link WiFi extender in the same room where you have placed the router.
    • Next, plug the extender into the power socket.
    • Within a minute, you have to press the WPS button located on your router. Now, wait for some time until the LED light turns green.
    • When the connection has been established properly between the D-Link extender and the wireless router, the LED light will turn solid green.

    At last, unplug your extender and place it in the desired place.

    Set up D-Link Extender Using WPS Method

How to Update Firmware for D-Link Extender?

 

Have you found that the speed of the D-Link WiFi internet degrades? Well, there could be several reasons behind this, such as outdated firmware. If you are using the outdated firmware of the Dlink extender, then you may face a connection issue. Go through the below steps to update the firmware for the D-Link extender to the latest available version:
 

Step 1: Open your computer. Launch any web browser of your choice from your system.

Step 2: Enter http://dlinkap.local admin login in the address bar of the web browser.

Step 3: You are redirected to the Dlink Extender Login page prompts you to enter the login credential details.

Step 4: Enter the username and password in the respective fields.

Step 5: Click on the login button.

Step 6: Go to the “Management” option located on the top menu.

Step 7: Tap on the “Upgrade” option from the drop-down menu.

Step 8: Next, choose the “check for new firmware” option. Thereafter, your extender will search for the availability of a new firmware version. If you found a new firmware update, then proceed with it.

Step 9: Choose the “update firmware” option. It will initiate the firmware update process.

 

Troubleshoot Tips to Resolve Issues with 192.168.0.50 Login

 

With the D-Link extender, you may face some issues during Dlink Extender Local setup. To fix these, you have to perform a reset process. It is the simplest process to reset the D-Link WiFi range extender. A simple reset can delete all the settings and configurations made by you.

Here are the steps to reset the extender:

Step 1: Before proceeding to the reset process, ensure that your D-Link extender is turned on.

Step 2: Remember not to plug out the extender during the setup process as it can damage the D-Link extender.

Step 3: Search for the Reset button on the back panel of your D-Link extender.

Step 4: Press and hold the “Reset” button using a needle or pin-pointed object.

Step 5: Release the reset button when the LED light on the extender lights up.

Step 6: Thereafter, the D-Link extender will restart automatically.

Note: The factory default process will delete all the settings you make, and thereafter, you have to configure the D-Link extender once again.

We hope that by following the above instructions, you can perform the Dlink extender local setup either through 192.168.0.50 login or dlinkap.local without any hassle.

Built on Unicorn Platform